View FBA1J4ALTE300P_4320728.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

KOA SPEER ELECTRONICS, INC.
SS-224 R5
AHA 10/27/04
Multilayer Ferrite Chip Bead Array Type FBA
1. Scope of Application Noise suppression in signal I/O lines and other circuits that require multiple chip beads for noise suppression. 1.1 Applications
I I
CERTIFIED
Computers Peripherals
I I
Telecommunications equipment Data communications
2. Features The Multilayer Ferrite Chip Bead Array retains all the features of Multilayer Ferrite Chip Beads. In addition, it provides multiple circuits in a single package, which reduce the required land space on PCB and reduce the cost for assembly. 3. Dimension and Structure
a W t Protective Coating Solder Plating L p b
Type
(Inch Size Code)
L .126.008 (3.20.2)
W .063.008 (1.60.2)
Dimensions inches (mm) t a .031.008 (0.80.2) .014.008 (0.350.2)
b .012.008 (0.30.2)
p .031.008 (0.80.2)
1J (0603)
3.1 Circuit
PAGE 1 OF 8 Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-224 R5
4. Ordering and Specifying Information*
FBA
Type
1J
Size
1J (0603)
4
Circuits
Number of Circuits
A
Characteristics
A: Standard B: High Speed
T
Termination Material
T: Sn L: SnPb
TE
Packaging
TE: 7" Embossed Plastic 3000 pcs/reel
300
Impedance
2 significant figure + 1 multipler Ex: 300 = 30
P
Tolerance
P: 25%
* Please note: KSE's part numbers do not contain any spaces or hyphens.
5. Standard Applications Ordering Code FBA1J4ATE300P FBA1J4ATE600P FBA1J4ATE121P FBA1J4ATE221P FBA1J4ATE301P FBA1J4ATE601P FBA1J4ATE102P FBA1J4BTE100P FBA1J4BTE220P FBA1J4BTE470P FBA1J4BTE600P FBA1J4BTE121P FBA1J4BTE221P FBA1J4BTE471P FBA1J4BTE601P Impedance @ 100MHz 30 60 120 220 300 600 1,000 10 22 47 60 120 220 470 600 Maximum DC Resistance 0.1 0.25 0.3 0.3 0.4 0.5 0.7 0.15 0.25 0.3 0.3 0.5 0.55 0.55 0.65 Allowable DC Current (mA) 200 400 350 250 250 100 200 200 200 150 350 100 100 100 100 -55C to 125C Operating Temperature
PAGE 2 OF 8 Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-224 R5
6. Graphs*
*
|Z| XL R
PAGE 3 OF 8
I
Bolivar Drive
I
P.O. Box 547
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-224 R5
6. Graphs* (continued)
*
|Z| XL R
PAGE 4 OF 8
I
Bolivar Drive
I
P.O. Box 547
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-224 R5
6. Graphs* (continued)
*
|Z| XL R
PAGE 5 OF 8
I
Bolivar Drive
I
P.O. Box 547
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-224 R5
6. Packaging Specifications KOA's multilayer components are provided on tape-and-reel for use in pick-and-place machines. The reel size is 7 inch. 7. Dimensions - inches (mm)
Do Po
P2
t
Tape 1J4
Ao
Bo
Ko
E F Bo
0.0710.002 0.1380.002 0.0480.002 (1.80.1) (3.50.1) (1.20.1)
W
Tape 1J4
E
F
W
D1 P1 Ao Ko
0.0690.004 0.1380.002 0.3180.002 (1.750.10) (3.50.005) (8.10.1)
Tape 1J4
P1
Po
P2
Do
D1
t 0.0090.001 (0.230.02)
0.1570.004 0.1570.004 0.0790.002 0.0590.004 0.039 min. (4.00.1) (4.00.1) (2.000.05) (1.5+0.1/-0.0) (1.0 min.)
8. Chip Quantities Per Reel Chip Size 1J4 Parts on 7 inch (178mm) Reel 3,000
9. Characteristics
Item Operating Temperature Storage Temperature Requirement -55C ~ +125C 40C @ 70% Humidity Sealed plastic bags with desiccant shall be used to reduce the potential of oxidation on the terminations during storage. Flux: 5-10 sec dip After Flux: Air dry for 15 sec Preheat: 150C 10C Preheat Time: 60 sec Solder Temp: 260C 5C Dip Time: 10 1 sec Conditions
Resistance to Solder Heat
Change in Impedance: Relative to value before test 20%. Appearance: There shall be no cracking Solder Coverage: More than 75% of the terminal electrode shall be covered with solder.
PAGE 6 OF 8 Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-224 R5
9. Characteristics (continued)
Item Solderability Requirement Solder Coverage: More than 95% of the termination shall be covered with solder. Conditions Flux: 5-10 sec dip After Flux: Air dry for 15 sec Solder Temp: 245C 5C Dip Time: 5 0.5 sec The bead shall be subjected to the following 5 steps for the period of time shown below. The 5 steps constitute one (1) rotation. 4 rotations shall be carried out. 1) Flux: 5-10 sec 2) After Flux: Air dry for 15 sec 3) Solder Temp: 230C 5C 4) Dip Time: 5 0.5 sec 5) Cool: Air cool for 60 seconds
Leach Resistance
Appearance: There shall be no visible signs of physical or mechanical damage (i.e. no cracks) Terminations: Termination must not be leached away for more than 5%.
Insulation Resistance Solvent Resistance
Insulation Resistance: Min 1G ohms Change in Impedance: Relative to value before test 10%. Cleaning by: Washer: Ultrasonic washer (100W) Solvent: Isopropyl alcohol Time: 3 minutes Type 1206 Type 1206 W(kgf) 1.5 W(kgf) 2.3 Time 30 sec 2 sec Time 60 sec
Terminal Strength (hanging test) Terminal Strength (push test) Bending Strength
Appearance: The terminal electrode shall not break off, nor shall there be damage to the body. Appearance: There shall be no evidence of mechanical degradations to terminals or body. Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value before test 10% Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value before test 10% Impedance: Relative to initial value 10%
Board: 90x40x1.6mm Bend: 1mm Time: 5 sec
Mechanical Shock
Force: 50G Time: 11 msec There shall be 3 shocks in each of 6 directions (18 shocks total). Only endurance conditioning by sweeping shall be made. The entire frequency range from 10-2,000Hz and return to 10Hz in 20 minutes (this shall constitute one cycle). Amplitude: 1.5mm The test shall have a 15G peak and shall be applied for a period of 4 hours (12 cycles) in each of 3 mutually perpendicular directions (a total of 36 cycles within a total of 12 hours).
Vibration
PAGE 7 OF 8 Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-224 R5
9. Characteristics (continued)
Item Thermal Shock Requirement Appearance: There shall be no physical or mechanical damage. Impedance: Relative to initial value 20%. DCR: The DCR shall not exceed initial specified value. Testing of the parts will be made at 0 hours, 250 hours and 500 hours. Before testing the parts shall be allowed to cool to room temperature for 24 hours. Load Humidity Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value 15% Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. Life Test Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value 15% Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. Temperature: 85C 2C Time: 1,000 hours total Apply: 100% rated current Conditions Step 1-start 2-hold 3-transfer 4-hold 5-transfer Temperature -40C 2C -40C 2C -- +105C 2C -- Time -- 30 min 5 min 0.5 min max. 30 min 5 min 0.5 min max.
Steps 1 thru 5 constitute one complete cycle and the test shall consist of a total of 500 cycles. Temperature: 85C 2C Relative Humidity: 85% Time: 1,000 hours total Apply: 100% rated current
10. Recommended PC Board Land Patterns - inches (mm)
Soldering Pad BW A E L Chip Component C Chip Component Size Size L W 1206 (3216) .126 (3.2) .063 (1.6) A B C E
.030 .120 .016 .031 (0.762) (3.048) (0.406) (0.787)
PAGE 8 OF 8 Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.

▲Up To Search▲

Price & Availability of FBA1J4ALTE300P

	To Download FBA1J4ALTE300P Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .